Country or region and language

    Choose your country or region and your language.

    Suggested for you

      All countries and regions

        Choose your character

        It shows in the top bar and on your profile. Change it any time.

        CompTIA A+ Core 1 practice test (220-1201)

        60 questions in 1 h. Target: 45 correct, a rough guide since CompTIA scores are scaled.

        A circuit board, a diagnostic computer and a screwdriver for A+ hardware practice.
        Questions
        60
        Time
        1 h
        To pass
        45 (75%)
        Mode
        Timed or untimed
        Access
        Free

        The practice test needs JavaScript. These are its questions:

        Help desk ticket: two laptops in a small office

        A small office has one SOHO router that also acts as its DHCP server. All wired desks connect through wall jacks to a patch panel, and the patch panel ports are patched into one office switch. A technician runs ipconfig on two Windows laptops. Laptop A works normally. Its results: IPv4 address 192.168.10.37, subnet mask 255.255.255.0, default gateway 192.168.10.1, DNS server 192.168.10.1. Laptop B belongs to a user who says the laptop shows a network connection but no internet. Its results: IPv4 address 169.254.88.14, subnet mask 255.255.0.0, default gateway blank, DNS server blank. Both laptops show a lit link light on their Ethernet port. Laptop B worked yesterday; this morning the user moved to a different desk, which uses a different wall jack and a different patch panel port.

        1. A technician is about to replace the memory in a business laptop that has a built-in battery. The maker's service manual lists the steps to take before the base cover comes off. Which approach matches it?

          1. Leave the AC adapter plugged in to keep the board grounded
          2. Shut down, unplug the adapter, and enter service mode
          3. Put the laptop to sleep so the memory contents are kept
          4. Pull the CMOS coin cell first so the firmware is reset
        2. After a WLAN card swap in a laptop, the new card is detected and joins the network, but signal strength is far weaker than it was before. Which oversight is the most likely cause?

          1. The new card needs a longer M.2 slot than the old card did
          2. The display cable was left loose on the system board
          3. The firmware still holds the old card's MAC address
          4. The antenna leads were left off or put on the wrong posts
        3. A user's new external webcam works well in video calls, but Windows 11 never offers Windows Hello Face as a sign-in option. What is the most likely reason?

          1. The camera lacks the near infrared sensor Hello Face needs
          2. Hello Face works only when a fingerprint reader is present
          3. The webcam must use a USB-C port rather than a USB-A port
          4. Face sign-in stays hidden until drive encryption is enabled
        4. A user wants to pay by holding an Android phone near a store's contactless card terminal. Which connection method must be turned on in the phone's settings?

          1. Bluetooth
          2. Wi-Fi hotspot
          3. NFC
          4. GPS location
        5. A user upgrades from an iPhone 14 to an iPhone 15 and finds that the charging cable from the old phone no longer fits. What changed?

          1. The iPhone 15 has a USB-C port in place of Lightning
          2. The iPhone 15 charges only wirelessly and has no port
          3. The iPhone 15 moved to a microUSB port for charging
          4. The iPhone 15 uses a miniUSB port for data and power
        6. A consultant tries to share an Android phone's cellular data with a MacBook over a USB cable, but USB tethering never works. Which option will get the Mac online through the phone?

          1. Swap in a USB 3.0 cable, since USB 2.0 cannot tether
          2. Turn on data roaming so the carrier allows wired sharing
          3. Enable airplane mode, then switch USB tethering back on
          4. Use the phone's Wi-Fi hotspot or Bluetooth tethering
        7. A frequent traveler wants to add a local carrier plan to an iPhone without inserting a physical SIM card. Which technology makes this possible?

          1. A microSD storage card
          2. An eSIM profile
          3. A Bluetooth pairing PIN
          4. A dual-band Wi-Fi radio
        8. Under a new BYOD policy, staff will use their own iPhones for company email and apps. The company wants to manage only its own accounts, apps and settings, never the employees' personal data. Which enrollment approach fits best?

          1. Wipe each phone and set it up as a shared corporate kiosk
          2. Skip MDM and give staff one shared password for the mail
          3. Account-driven User Enrollment through the MDM service
          4. Device Enrollment with every restriction payload applied
        9. A new Bluetooth headset does not appear under new devices in Windows 11, although Bluetooth is switched on in Settings. Which step was most likely missed?

          1. Typing the headset's PIN before turning Bluetooth on
          2. Testing a call on the headset before pairing it
          3. Installing a Wi-Fi driver, as Bluetooth runs over Wi-Fi
          4. Putting the headset into pairing mode to make it visible
        10. A firewall must allow inbound Remote Desktop connections to a Windows server that still uses the default settings. Which port should the rule open?

          1. 3389
          2. 443
          3. 22
          4. 445
        11. A user reads one mailbox on a phone, a laptop and a tablet and wants messages and folders kept on the server so every device shows the same state. Which protocol and default cleartext port should the mail client use to retrieve mail?

          1. POP3 on port 110
          2. SMTP on port 25
          3. IMAP on port 143
          4. LDAP on port 389
        12. Which statement about the transport used by DNS and DHCP is correct?

          1. DNS uses only TCP 53, and DHCP uses TCP 67 and 68
          2. DNS can use UDP or TCP 53; DHCP uses UDP 67 and 68
          3. DNS uses only UDP 53, and DHCP uses TCP 67 and 68
          4. Both run on TCP only, since both need guaranteed delivery
        13. A spec sheet describes a new access point as Wi-Fi 6. Which IEEE standard does that generation name identify?

          1. 802.11n
          2. 802.11ac
          3. 802.11g
          4. 802.11ax
        14. A technician is installing three access points in a row in a US office. All three use the 2.4 GHz band with 20 MHz channels. Which channel plan keeps neighboring APs from overlapping?

          1. Channels 1, 6 and 11
          2. Channels 1, 2 and 3
          3. Channels 2, 5 and 8
          4. Channel 6 on all three
        15. An office creates a new SSID that broadcasts only in the 6 GHz band. Laptops with Wi-Fi 6E adapters see it, but a laptop with a Wi-Fi 5 (802.11ac) adapter does not. Why?

          1. 802.11ac adapters can only see networks with WPA3 off
          2. 6 GHz support arrived after the Wi-Fi 5 generation
          3. The SSID must be set to 20 MHz to reach older adapters
          4. Wi-Fi 5 adapters work only in 2.4 GHz, not 5 or 6 GHz
        16. An online shop runs three identical web servers. Which appliance spreads incoming client requests across them and stops sending traffic to a server that fails its health checks?

          1. Proxy server
          2. Spam gateway
          3. Load balancer
          4. Syslog server
        17. Several domain-joined PCs suddenly cannot sign users in to the domain. Their clocks are 7 minutes behind the domain controller's. Which service should the technician fix first?

          1. NTP time sync, as Kerberos allows 5 minutes of skew
          2. DHCP, as the clock drift made every lease expire
          3. DNS, as a wrong clock corrupts the server's A records
          4. Syslog, as sign-ins stop when log times don't match
        18. Which DNS record type tells sending mail servers which host accepts email for a domain?

          1. A
          2. CNAME
          3. TXT
          4. MX
        19. A network printer gets its address from DHCP, but users lose it whenever the address changes. The admin wants the printer to keep the same address while DHCP still hands it out. What should be configured on the DHCP server?

          1. An exclusion range that covers the printer's address
          2. A shorter lease time so the printer renews more often
          3. A reservation tied to the printer's MAC address
          4. A second scope created just for the printer subnet
        20. A company already publishes SPF and DKIM for its domain. It now wants receiving servers to reject messages claiming to be from its domain that fail those checks, and to send it daily aggregate reports. What should it add to DNS?

          1. A TXT record at the domain root reading v=spf1 -all
          2. A TXT record at _dmarc with p=reject and an rua address
          3. An MX record that points to a report-collecting server
          4. A CNAME at the DKIM selector that points to the provider
        21. A new security camera's datasheet says it needs an IEEE 802.3at (PoE+) port. The office switch's PoE ports follow only IEEE 802.3af. Which option will power the camera properly?

          1. An 802.3at port or injector that can supply up to 30 W
          2. The existing 802.3af port, which also supplies 30 W
          3. An 802.3af port with a shorter patch cable to the camera
          4. A non-PoE gigabit port, since data and power are separate
        22. A small office wants guest devices on a separate VLAN from staff PCs, all plugged into the same switch. What kind of switch does this require?

          1. Unmanaged, since VLANs live on the router
          2. A patch panel with color-coded ports
          3. A cable modem that has four LAN ports
          4. Managed, with VLAN support configured
        23. What does Laptop B's IPv4 address tell the technician?

          1. It holds a public address that the ISP assigned to it
          2. It gave itself a link-local address after DHCP failed
          3. It has a static address that conflicts with Laptop A
          4. It took a lease from a second DHCP server on the LAN
        24. Which statement about Laptop A's address and subnet is correct?

          1. It is a public address, so the router sends it to the internet as is
          2. Its subnet holds 65,534 hosts, because it starts with 192.168
          3. It is a private RFC 1918 address in a subnet with 254 usable hosts
          4. It is a link-local address, so it cannot reach its default gateway
        25. A remote field office uses traditional geostationary satellite internet. Downloads are acceptable, but video calls and remote desktop sessions feel sluggish and laggy. What best explains this?

          1. High latency from the long trip up to orbit and back
          2. Satellite links carry only UDP, so TCP apps must retry
          3. A legal cap holds satellite uploads to dial-up speeds
          4. Geostationary links drop and redial every few minutes
        26. In a wiring closet, dozens of unlabeled cables run from a patch panel to offices. Which tool lets a technician find which cable ends at one particular wall jack?

          1. Loopback plug
          2. Crimper
          3. Wi-Fi analyzer
          4. Toner probe
        27. Which display technology needs no backlight, because each pixel makes its own light and can turn off fully for true black?

          1. IPS LCD
          2. TN LCD
          3. OLED
          4. VA LCD
        28. A design team needs monitors whose colors stay accurate when people view them from the side during reviews. A gamer on a budget wants the fastest response time. Which pairing fits these needs?

          1. TN for the design team and IPS for the gamer
          2. IPS for the design team and TN for the gamer
          3. VA for both, since VA has the fastest response
          4. TN for both, since TN has the widest angles
        29. Two campus buildings are 2 km apart and need a 10 Gb/s fiber link using standard SFP+ optics. Which combination works?

          1. Single-mode fiber with 10GBASE-LR optics
          2. OM3 multimode fiber with 10GBASE-SR optics
          3. OM4 multimode fiber with 10GBASE-SR optics
          4. OM4 multimode fiber with 10GBASE-ER optics
        30. Network cable must run through the air-return space above a suspended ceiling, where the HVAC system moves air. Which cable should be used?

          1. Direct burial cable
          2. Standard PVC patch cable
          3. Shielded outdoor cable
          4. Plenum-rated cable
        31. A laptop has two identical-looking USB-C ports, but only one has a lightning bolt symbol beside it. The user's new dock is a Thunderbolt dock. Which port should the dock use?

          1. Either one, since all USB-C ports carry Thunderbolt
          2. The unmarked one, since the bolt marks charging
          3. The port with the Thunderbolt symbol
          4. Neither; Thunderbolt docks need a DisplayPort jack
        32. A file server must keep running correctly even if a memory cell occasionally flips a bit. Which memory feature is designed for this?

          1. ECC, which finds and corrects single-bit errors
          2. Higher CAS latency, which slows reads for safety
          3. SODIMM modules, which are made for servers
          4. Dual-channel mode, which stores two data copies
        33. A desktop board has four memory slots labeled A1, A2, B1 and B2. A user installs a two-module kit in A1 and A2, and the system reports single-channel mode. What fixes it?

          1. Add a third module so the board can interleave
          2. Move the modules to A2 and B2, one per channel
          3. Turn on ECC in the firmware to unlock dual-channel
          4. Swap in SODIMMs, which are built for dual-channel
        34. Two M.2 SSDs look almost the same. One talks to the system over PCIe using NVMe; the other uses SATA. Which statement is correct?

          1. Both use the same interface, so their speed is identical
          2. The SATA drive sends its commands to the host over NVMe
          3. NVMe is a form factor, while M.2 is the command set
          4. The NVMe drive uses a command set built for PCIe
        35. A server has four 4 TB drives configured as one RAID 5 array. How much usable space does the array provide, and how many drive failures can it survive without data loss?

          1. 16 TB; it cannot survive any drive failure
          2. 8 TB; it survives one failure in each mirror
          3. 12 TB; it can survive one drive failure
          4. 12 TB; it can survive any two drive failures
        36. An admin wants a database volume that combines mirroring and striping. What is the minimum number of drives for RAID 10, and how much of the raw capacity is usable?

          1. Three drives, with two thirds usable
          2. Four drives, with half usable
          3. Two drives, with all of it usable
          4. Four drives, with three quarters usable
        37. A desktop fails a Windows 11 upgrade check. Which security chip feature does Microsoft list among the minimum system requirements?

          1. TPM version 2.0
          2. A hardware security module card
          3. Legacy BIOS boot mode
          4. A BIOS boot password
        38. What does turning on Secure Boot in a PC's UEFI settings do?

          1. Encrypts the system drive with a key kept in the TPM
          2. Asks for a password before firmware setup will open
          3. Lets only boot software with valid signatures load
          4. Blocks the USB ports until the OS has fully started
        39. A sales team moves to Windows 11 laptops with Arm processors. Their x64 office apps run fine, but an old label printer works only with an x64 kernel-mode driver. What should the technician expect?

          1. The driver runs under emulation, just as the x64 apps do
          2. The driver will load once the laptop is set to 32-bit mode
          3. Turning on Secure Boot lets the x64 driver load on Arm
          4. The driver will not load; an Arm64 driver is required
        40. A desktop's components are drawing 450 W from its power supply, and at that load the PSU runs at 90% efficiency. About how much power does the PSU draw from the wall outlet?

          Efficiency = DC power out / AC power in

          1. 405 W
          2. 500 W
          3. 450 W
          4. 540 W
        41. A new ATX power supply is going into an older system whose motherboard has a 20-pin main power socket. The PSU's main cable is 24-pin. What should the technician do?

          1. Detach the cable's 4-pin section and plug in the 20 pins
          2. Replace the motherboard, since 24-pin plugs never fit it
          3. Push the spare 4 pins into the CPU's 8-pin 12 V socket
          4. Feed the missing pins from a SATA-to-Molex adapter
        42. An office of 60 users has 12 network printers. IT wants one place to share all the printers, push drivers to clients and manage the print queues. What should it deploy?

          1. A USB hub attached to each printer
          2. Direct IP printing set up on each PC
          3. The print server role on a Windows server
          4. A syslog server that collects printer logs
        43. A LaserJet shows an alert recommending a maintenance kit, and its pages are starting to come out wrinkled. What does a typical LaserJet maintenance kit contain?

          1. Toner cartridge, imaging drum and developer
          2. Printhead, ink cartridges and a cleaning pad
          3. Ribbon, impact printhead and tractor feeder
          4. Fuser, transfer roller and feed rollers
        44. A shipping-label printer prints with no ink, toner or ribbon. What does it print on, and what is its routine printhead cleaning?

          1. Plain copy paper; wipe the drum with a dry cloth
          2. Heat-sensitive media; clean with isopropyl alcohol
          3. Multipart forms; replace the ribbon and the printhead
          4. Glossy photo paper; run a nozzle check and clean
        45. Which kind of hypervisor runs directly on the computer's hardware instead of running as an application on a host operating system?

          1. A Type 2 hypervisor such as VirtualBox
          2. A container engine such as Docker
          3. A Type 1 hypervisor such as Hyper-V
          4. An emulator for x64 apps on Arm PCs
        46. A developer wants to run many isolated copies of one application on a server with less overhead than full virtual machines. Why are containers lighter than VMs?

          1. They share the host's kernel instead of booting an OS
          2. They run a full guest OS that has its own kernel
          3. They must run on a Type 2 hypervisor on the host
          4. They can run any OS version, unlike full virtual machines
        47. A technician must open a suspicious email attachment on a Windows 11 Pro PC without risking the host, and nothing should be left behind afterward. Which built-in feature fits best?

          1. A second local user account on the same PC
          2. A Remote Desktop session to the same PC
          3. Compatibility mode on the program used
          4. Windows Sandbox, discarded when it closes
        48. A technician tries to add Hyper-V to a Windows 11 Pro desktop. The CPU supports Intel VT-x and SLAT, and the PC has 16 GB of RAM, but systeminfo reports that virtualization is not enabled in the firmware. What should be done?

          1. Move to Windows 11 Home, which ships with Hyper-V
          2. Enable Intel VT in the UEFI setup and try again
          3. Add RAM, since this message really means low memory
          4. Install a Type 2 hypervisor first to unlock Hyper-V
        49. A company uses a provider's web-based email and office apps. It manages user accounts but never touches servers, operating systems or storage. Which cloud service model is this?

          1. SaaS
          2. PaaS
          3. IaaS
          4. Private cloud
        50. Several hospitals that share the same compliance rules jointly set up cloud infrastructure that only their organizations may use. Which deployment model is this?

          1. Public cloud
          2. Hybrid cloud
          3. Community cloud
          4. Private cloud
        51. An online store's cloud servers add capacity automatically during a holiday traffic spike and release it when traffic drops. Which cloud characteristic is this?

          1. Metered utilization
          2. Elasticity
          3. Multitenancy
          4. File synchronization
        52. A team uploads 50 TB of archives to Azure storage and plans to download most of it back to the office every month for analysis. Which part of the bandwidth bill is most likely to grow?

          1. Data transfer in, since uploads are billed per GB
          2. None, since metered services never bill bandwidth
          3. A one-time fee for moving data into the region
          4. Data transfer out (egress), billed per GB
        53. Each time an older desktop is unplugged overnight, it boots with the wrong date and time and its firmware settings back at defaults. Which part should the technician replace?

          1. The CMOS coin-cell battery
          2. The power supply unit
          3. The system drive (SSD or HDD)
          4. The memory modules
        54. A desktop powers on with fans spinning but shows no video, and it repeats a beep pattern that the maker's chart lists as a memory failure. What is the best first step?

          1. Fit a higher-wattage power supply
          2. Reinstall Windows from recovery media
          3. Reseat the RAM, then test each module
          4. Replace the CPU and its cooler at once
        55. A laptop shuts itself off during long video renders. The fan is loud, the underside is very hot, and the user often works with the laptop on a bed. What is the most likely cause?

          1. A weak CMOS battery that keeps resetting the clock
          2. Too little free disk space for the render files
          3. A display cable that has worked loose inside
          4. Blocked air vents and dust that stop the airflow
        56. Right after a user adds a second RAM module, Windows starts restarting with the same stop code (blue screen) error. Which step should come first?

          1. Reinstall Windows to clear out corrupted system files
          2. Remove the new module and see whether the errors stop
          3. Fit a bigger power supply, as new RAM needs more power
          4. Update every application installed on the computer
        57. A desktop's hard drive starts making repeated hard clicking sounds, sometimes with a grinding noise. What should the technician do first?

          1. Defragment the drive to cut down on head movement
          2. Run a full format so it maps out the bad sectors
          3. Make sure a full backup of important data exists
          4. Keep using it, as clicking only means head parking
        58. After a firmware settings reset, a Windows 11 PC that was installed in UEFI mode shows a No bootable device found error. The system drive still appears in firmware setup. What should the technician check first?

          1. Whether boot mode changed to Legacy; set UEFI again
          2. Whether the drive needs a low-level format to boot
          3. Whether the array needs one more disk to come online
          4. Whether Windows must be reinstalled in Legacy mode
        59. On a PC using Intel Rapid Storage Technology, one drive in a RAID 1 volume failed and was replaced with a new drive of the same size. Hours later the volume still shows as degraded. What is expected next?

          1. Nothing; RST starts the rebuild at the next restart
          2. Replace the other drive too, so the pair is the same age
          3. Delete the volume and restore it all from backup
          4. Choose Rebuild to another disk and pick the new drive
        60. Laptop B shows a link light but cannot reach the internet. What should the technician do next?

          1. Check that the new jack's patch panel port goes to the switch
          2. Give Laptop B the static address 169.254.88.1 with no gateway
          3. Point Laptop B's DNS at a public resolver, then reboot
          4. Replace Laptop B's network card, since APIPA means it failed

        What this set covers

        • Mobile device hardware3 questions
        • Mobile accessories and connectivity3 questions
        • Mobile network and app support3 questions
        • Ports and protocols3 questions
        • Wireless networking3 questions
        • Networked host services2 questions
        • Network configuration3 questions
        • Networking hardware2 questions
        • SOHO IP addressing2 questions
        • Internet connection types1 questions
        • Networking tools1 questions
        • Displays2 questions
        • Cables and connectors3 questions
        • RAM2 questions
        • Storage and RAID3 questions
        • Motherboards, CPUs and firmware3 questions
        • Power supplies2 questions
        • Printer deployment1 questions
        • Printer maintenance2 questions
        • Virtualization4 questions
        • Cloud computing4 questions
        • Troubleshooting motherboard, RAM, CPU and power4 questions
        • Troubleshooting drives and RAID3 questions
        • Troubleshooting networks1 questions

        Next: Core 2 practice test

        More practice for this exam

        1. Core 2 practice test60 questions · 1 h
        2. Quick practice test20 questions · 20 min

        All practice for the CompTIA A+

        Independent practice. The Work Gym isn't affiliated with CompTIA, and these aren't official CompTIA questions. CompTIA A+® is a registered trademark of CompTIA, Inc.

        Your Work Gym account

        Save your progress and pick up on another device. Your browser's progress comes with you.

        or

        You can keep practicing without an account.

        Change your plan

        Checking the price

        Help and feedback

        Ask a question, tell us what is not working, or share an idea. We reply by email.

        What is it about?

        We use it only to reply to you.