Country or region and language

    Choose your country or region and your language.

    Suggested for you

      All countries and regions

        Choose your character

        It shows in the top bar and on your profile. Change it any time.

        Controls engineer skills and practice

        Write a PLC program, run a sequence of input changes and check the machine's response. This path covers the programming part of controls engineering through connected machine projects, fault investigations and original job assessments.

        Tools
        PLC programming
        Units
        12 units, 61 lessons
        Checked exercises
        344
        Cross-tool projects
        0
        Final assessment
        12 tasks, 45 minutes

        About 26 hours of lessons, from the estimate on each lesson.

        Your progress

        Nothing done yet. Progress saves in this browser as you finish lessons, and in your account when you sign in.

        Lessons
        0 of 61 lessons
        Projects
        0 of 0 finished
        Assessment
        Not taken yet

        Start with Signals and scan order

        The pathway, unit by unit

        Take the steps in this order. Each step is a set of units from one course, not the whole course: the units this role uses. Open a unit to start its first lesson.

        1. Signals and the scan cycle

          Read tags and contact conditions, build permissives and follow how rung order changes the result. Test a released button and a broken permissive as well as the normal operating state.

          1. Signals and scan orderBeginner · 4 lessons · 20 exercisesFree
          2. Permissives and remembered stateBeginner · 4 lessons · 20 exercises
          3. Scan-aware controlBeginner · 5 lessons · 28 exercises
        2. Timing, counting and analog values

          Distinguish elapsed time from scan counts. Count rising edges, reset memory and test values exactly at a threshold. The trace shows what changed after each scan.

          1. Timers and interrupted conditionsIntermediate · 5 lessons · 27 exercises
          2. Counters and production totalsIntermediate · 6 lessons · 34 exercises
          3. Compare and math blocksIntermediate · 5 lessons · 27 exercises
        3. Machines, structured text and HMI

          Program conveyor, tank, traffic-light and packaging scenarios. Use the supported structured text subset, bind HMI tags and separate an alarm condition from its acknowledgment.

          1. Machine sequencesAdvanced · 5 lessons · 27 exercises
          2. Structured TextAdvanced · 5 lessons · 28 exercises
          3. HMI tags and alarmsAdvanced · 5 lessons · 27 exercises
        4. Fault investigation and handoff

          Reproduce a fault, make a bounded repair and test the restart behavior. Connected projects retain your program between steps. The path ends with independent interview tasks and a timed assessment.

          1. Fault finding on running programsExpert · 5 lessons · 27 exercises
          2. Packaging and deliveryExpert · 6 lessons · 35 exercises
          3. Controls engineering assessmentExpert · 6 lessons · 44 exercises

        Projects for this role

        Each project starts from a fictional company's brief and moves between tools the way the job does: what you build in one stage is where the next one starts. Every brief is free to read.

        The job-readiness assessment

        When you finish the units, test yourself across the tools of the job at once: 12 practical tasks in 45 minutes, each in the tool it is about and checked automatically. The clock keeps running if you close the page.

        ToolTasksMinutes
        PLC programming1245

        How it is scored

        Each tool
        Ready when you get two thirds of its tasks right or more, Close at one third, otherwise Not yet. A coding task earns the share of its tests that pass.
        Ready for interviews
        75% or more overall, and every tool at Ready.
        Nearly ready
        50% or more overall, and no tool at Not yet.
        Keep practicing
        Anything else. The report lists every task you missed with the lesson that teaches it.

        Open the assessment

        The assessment is free. The result is practice feedback in the Interview Hub's report format, not a hiring decision. Retakes draw different tasks where the question pools allow.

        The interview

        The Interview Hub runs the controls engineer interview round by round, at a fictional employer: you answer out loud or in writing, the interviewer follows up, and the report quotes your answers.

        Practice the controls engineer interview

        What each plan opens

        Free
        The first unit of every course, with no account: 1 of the 12 units on this pathway. Every project brief is free to read, and the job-readiness assessment is free.
        One Course
        One course in full. On this pathway that is one of these: PLC programming (12 units).
        All Access
        The whole pathway: every unit, every project stage and spoken interview practice.

        See plans and prices

        PLC programming

        Start with the PLC programming course. A rung that starts a motor must also behave correctly when the request disappears or a permissive opens. Watch the inputs and outputs through the whole sequence before you call a program finished.

        Machine projects

        The course projects connect requirements across several steps. Your program carries forward, so each change has to preserve the earlier behavior. The projects stay inside the PLC workspace; this path doesn’t include a separate cross-tool portfolio project.

        Field experience

        A correct browser trace establishes behavior inside a simplified model. A physical machine adds wiring, actuator failure, communication delays and safety requirements that this model cannot validate. Use the simulation to prepare questions and test reasoning before supervised practical training.

        Common questions

        Does this qualify me to commission machinery?

        No. These are browser programming exercises. Electrical installation, safety validation, vendor configuration and supervised work on physical equipment need separate training and authorization.

        Is this Siemens or Allen-Bradley software?

        The PLC simulator is our own generic workspace. Contacts, coils, timers and scan reasoning transfer, but vendor syntax, hardware setup and task scheduling differ. Consult the target platform's documentation.

        What should I show in an interview?

        Explain a program and the input sequence that could expose its failure. Keep the scan trace, the observed output and the reason for the repair. The controls engineer interview gives you independent tasks to practice that explanation.

        Your Work Gym account

        Save your progress and pick up on another device. Your browser's progress comes with you.

        or

        You can keep practicing without an account.

        Help and feedback

        Ask a question, tell us what is not working, or share an idea. We reply by email.

        What is it about?

        We use it only to reply to you.